Turkish Drywall Wall Profile Manufacturing
Turkish Drywall wall profiles are materials used in many areas. It is useful in the construction of partition walls while prefabricated structures are manufactured in interior wall applications. Using this material, insulation and coating can be made on the roofs and walls of the buildings.
Drywall wall profile is extremely durable. It can be preferred for use in large areas thanks to its economy. It allows you to hide materials that do not look like electrical and plumbing. Drywall Wall Profile Manufacturing. Thanks to this feature, it allows you to get a decorative appearance. By being painted, it easily adapts to your decoration.
Wall C50 Profile Manufacturing
Wall C50 profile is used in interior partition, Turkish drywall and shaft wall applications by adjusting its metal carrier frame to 50 mm. The application is made by inserting it into the wall U profiles. Then plasterboard is applied. When making a drywall, it is sufficient to screw on one side of the profile.
It can be assembled in a short time. Likewise, it is easy to disassemble. It does not cause any loss of space on the walls. It is 9 times lighter than brick structures. Drywall Wall Profile Manufacturing. This allows the building to be flexible. It does not break immediately in a severe shake such as an earthquake. Wall C profile insulates sound and heat in the area where it is used. It is resistant to fire. It can be produced in any desired size for use in different areas.
Material Thickness (mm)
Length (mm)
Weight (kg)
Standard
Producible Sizes
DC-50 DIN 50x49x0.50
3000
2500-6000
0.590
DC-50 EKO TSE 50x49x0,60
0.707
DC-50 EKO TSE 50x40x0,50
3000
2500-6000
0.538
DC-50 EKO TSE 50x40x0,60
0,646
Wall U50 Profile Manufacturing
Where the wall U50 profile will be applied, the metal carrier frame is adjusted to 75 mm and used. It ensures that the Wall C profile and the partition wall are in balance. Drywall Wall Profile Manufacturing. Plasterboard is applied to the junction of the floor and ceiling in wall construction. It is produced in accordance with the EN 14195 quality standard. Since it is a light material, it does not put much load on the building it is used in.
Material Thickness (mm)
Length (mm)
Weight (kg)
Standard
Producible Sizes
DU-50 DIN 50x35x0.50
3000
2500-6000
0.456
DC-50 EKO TSE 50x35x0,60
0.547
DC-50 EKO TSE 50x27x0,50
3000
2500-6000
0.393
DC-50 EKO TSE 50x27x0,60
0.472
Turkish Wall Corner Profile Manufacturing
Wall corner profile is made of galvanized material. Therefore, it has the advantages of galvanized coating. Since it is resistant to corrosion, it can be used outdoors as well as indoors. Drywall Wall Profile Manufacturing. It provides protection against any damage in the area of use. It can be applied in corners to get a steep look. Materials with wall thicknesses of 0.35 and 0.45 mm can be produced.
How to Apply Turkish Wall C and Wall U Profile?
It can be said that wall C and wall U profiles are complementary to each other. For their application, the measurements of the space are first taken with a laser meter. Drywall Wall Profile Manufacturing If a partition wall is to be built, its location is determined. The wall to which the U profile will be fixed is fixed to the floor with a line of string. Using the mark on the floor, a mark is made on the ceiling with a plumb line. After deciding on the length of the wall, U and C profiles are cut to the desired size. C profiles are cut 1 cm shorter than the ceiling height to provide convenience during installation.
Before starting the assembly process, soundproofing tapes are attached to the bottom of the profiles. The number of C profiles to be used is calculated by giving a 60 cm interval. Drywall Wall Profile ManufacturingF For places to be covered with materials such as ceramic and marble, this range should be less. After the plan phase is completed, installation can be started. First, U profiles are fixed to the floor and ceiling with the help of screws. Screwing is done every 60 cm. Then C profiles are started to be attached. After the first C profile is fixed, the others are fixed by rotating between the U profiles. C profiles are not fixed to U profiles since the corex application will be done later.
