Turkisk gipsväggprofiltillverkning

Turkiska gipsväggsprofiler är material som används inom många områden. Det är användbart vid konstruktion av skiljeväggar medan prefabricerade strukturer tillverkas i innerväggsapplikationer. Med detta material kan isolering och beläggning göras på byggnadernas tak och väggar.

Drywall wall profile is extremely durable. It can be preferred for use in large areas thanks to its economy. It allows you to hide materials that do not look like electrical and plumbing. Drywall Wall Profile Manufacturing. Thanks to this feature, it allows you to get a decorative appearance. By being painted, it easily adapts to your decoration.

Wall C50 Profiltillverkning

Vägg C50 profil används i interiöra skiljeväggar, turkiska gipsväggar och schaktväggar genom att justera dess metallbärarram till 50 mm. Appliceringen görs genom att den sätts in i väggens U-profiler. Därefter appliceras gipsskivor. När du gör en gipsskiva räcker det att skruva på ena sidan av den profil.
It can be assembled in a short time. Likewise, it is easy to disassemble. It does not cause any loss of space on the walls. It is 9 times lighter than brick structures. Drywall Wall Profile Manufacturing. This allows the building to be flexible. It does not break immediately in a severe shake such as an earthquake. Wall C profile insulates sound and heat in the area where it is used. It is resistant to fire. It can be produced in any desired size for use in different areas.

 

Materialtjocklek (mm)
Längd (mm)

vikt (kg)

Standard
Producerbara storlekar

DC-50 DIN 50x49x0,50
3000
2500-6000
0.590

DC-50 EKO TSE 50x49x0,60
0.707

DC-50 EKO TSE 50x40x0,50
3000
2500-6000
0.538

DC-50 EKO TSE 50x40x0,60
0,646

Wall U50 Profiltillverkning

Where the wall U50 profile will be applied, the metal carrier frame is adjusted to 75 mm and used. It ensures that the Wall C profile and the partition wall are in balance. Drywall Wall Profile Manufacturing. Plasterboard is applied to the junction of the floor and ceiling in wall construction. It is produced in accordance with the EN 14195 quality standard. Since it is a light material, it does not put much load on the building it is used in.

Materialtjocklek (mm)
Längd (mm)

vikt (kg)

Standard
Producerbara storlekar

DU-50 DIN 50x35x0,50
3000
2500-6000
0.456

DC-50 EKO TSE 50x35x0,60
0.547

DC-50 EKO TSE 50x27x0,50
3000
2500-6000
0.393

DC-50 EKO TSE 50x27x0,60
0.472

Turkisk vägghörnprofiltillverkning

Wall corner profile is made of galvanized material. Therefore, it has the advantages of galvanized coating. Since it is resistant to corrosion, it can be used outdoors as well as indoors. Drywall Wall Profile Manufacturing. It provides protection against any damage in the area of ​​use. It can be applied in corners to get a steep look. Materials with wall thicknesses of 0.35 and 0.45 mm can be produced.

 

How to Apply Turkish Wall C and Wall U Profile?

It can be said that wall C and wall U profiles are complementary to each other. For their application, the measurements of the space are first taken with a laser meter. Drywall Wall Profile Manufacturing If a partition wall is to be built, its location is determined. The wall to which the U profile will be fixed is fixed to the floor with a line of string. Using the mark on the floor, a mark is made on the ceiling with a plumb line. After deciding on the length of the wall, U and C profiles are cut to the desired size. C profiles are cut 1 cm shorter than the ceiling height to provide convenience during installation.

Before starting the assembly process, soundproofing tapes are attached to the bottom of the profiles. The number of C profiles to be used is calculated by giving a 60 cm interval. Drywall Wall Profile ManufacturingF For places to be covered with materials such as ceramic and marble, this range should be less. After the plan phase is completed, installation can be started. First, U profiles are fixed to the floor and ceiling with the help of screws. Screwing is done every 60 cm. Then C profiles are started to be attached. After the first C profile is fixed, the others are fixed by rotating between the U profiles. C profiles are not fixed to U profiles since the corex application will be done later.